The device, service and repair of Honda Accord - Removal and installation of a latch and the external handle / cylinder of the lock of a door//Honda the Chord of 1998-1999 of century /

Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle / cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ Schemes of electric equipment





Removal and installation of a latch and external handle / cylinder of the lock of a door

For protection of hands against cuts when performing procedures through access openings in a doorframe put on gloves.

Assembly of a latch of the lock

 PERFORMANCE ORDER

1. Lift a windowpane, then remove the panel of an internal upholstery of a door and the moisture filter (see the Section Removal and installation of panels of an internal upholstery of doors).

2. Through a big opening in a doorframe disconnect the rod connecting the external handle to a latch. Do the same with a rod of the internal handle, and also with rods of external and internal locks and (at the corresponding complete set) the electromagnetic actuation mechanism.

3. All rods fasten by means of plastic clamps. Release the part of a clamp entering gearing with a rod, then pull a rod, releasing it from a landing opening. On the models equipped with the uniform lock, disconnect the corresponding electrical wiring from assembly of a latch.

4. Turn out screws of fastening of a latch to a door. Take assembly of a latch through the opening provided in a doorframe.

5. Installation is made upside-down.

External handle and cylinder of the door lock

 PERFORMANCE ORDER

1. Close a window and remove the panel of an internal upholstery of a door and the moisture filter (see the Section Removal and installation of panels of an internal upholstery of doors).

In order to avoid damage of a paint and varnish covering of the door panel paste over with an adhesive tape a window under landing of the door handle.

2. Through a special opening in a doorframe release plastic clamps of fastening to a latch of executive rods external the handle and the lock of a door.
3. Take caps, then turn out bolts of fastening of the external handle.

4. Remove the handle assembled with the lock cylinder. In case of need the cylinder can be taken from assembly by a clamp otpuskaniye. At the corresponding complete set of the car the socket of an electrical wiring is removed by an otdavaniye of a fixing bolt.

5. Installation is made upside-down.