Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle / cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ Schemes of electric equipment




Removal and installation of finishing sections of the dashboard

The models of cars considered in the present manual are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving injuries at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation.


 PERFORMANCE ORDER

Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for input of the audio system in action!

Facing of an instrument guard

 PERFORMANCE ORDER

1. At the corresponding complete set of the car lower a steering column in the lower situation.

2. Turn out two fixing screws in the top part of facing.

3. Accurately hooking a screw-driver, release clamps and separate the lower part of facing of a guard from the dashboard. Not to scratch a surface of the panel close up a screw-driver sting with an adhesive tape.
4. Installation is made upside-down. Track reliability of a zashchelkivaniye of clamps.

Knee emphasis

 PERFORMANCE ORDER

1. Remove a forward cover of the central console (see the Section Removal and installation of the central console).

2. Having hooked, remove a plastic cover of the assembly block of safety locks under the dashboard at the left. Turn out two fixing screws located under a cover.

3. Turn out the right top screw of fastening of a knee emphasis, then hook assembly, releasing fixing clamps.

4. If it is necessary to provide access to the components located under the dashboard, turn out bolts of fastening of a stiffening rib of assembly of a knee emphasis. Delay bottom edge of an edge and take assembly from salon of the car.
5. Installation is made upside-down.

Central section

 PERFORMANCE ORDER

1. Having hooked the screw-driver wound by an adhesive tape, remove facing of assembly of panel hours.

2. Having released facing, disunite sockets of an electrical wiring of hours and the switch of the alarm system.

3. Turn out screws of fastening of the central section of the dashboard. One of screws is located in the top dredging under landing of facing of hours, two - from below. The rest of the panel fastens by means of plastic clamps.

4. The control panel functioning of the heater/conditioner of air fastens to the dashboard by means of the screws screwed behind. Release the panel from the landing nest, disconnect an electrical wiring and remove assembly.

5. Installation is made upside-down.

Right lower section of the dashboard, ware box

 PERFORMANCE ORDER

1. Removal of the lower lateral cover from the passenger party of the dashboard is made similar to removal of assembly of a knee emphasis. Having hooked, remove a face cover of the dashboard (for the purpose of ensuring access open a passenger door) and turn out two fixing screws. The third screw is located in the left top corner of the panel.

2. Hooking bottom edge of the panel, serially release clamps of its fastening. Remove the panel.

3. Turn out screws of fastening of bottom edge of assembly of a ware box.

4. Open a box door, by means of a screw-driver remove plastic caps and turn out screws of fastening of the upper edge of assembly.

5. Wring out loops of a door of a ware box in the direction to each other for the purpose of an otpuskaniye of fixing clamps, then pull assembly down and outside, releasing it from the panel.

Having released assembly of a ware box from the panel, disunite the socket of an electrical wiring of its illumination.

6. Installation is made upside-down.