Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
- Power supply system and release
   Dropping pressure in a power supply system
   Check of serviceability of functioning of the fuel pump, measurement of pressure of fuel
   Check of a state and replacement of fuel lines
   Removal and installation of the fuel pump
   Check of a state and replacement of the sensor
   Removal and installation of a fuel tank
   Cleaning and repair of a fuel tank - general information
   Removal and installation of assembly of the air cleaner
   Removal, installation and adjustment of a cable of an accelerator
   System of electronic injection of fuel (EFI) - the general information
   Check of serviceability of functioning of system of injection
   Removal and installation of the case of a throttle
   Removal and installation of the regulator of pressure of fuel
   Removal and installation of the fuel highway and injectors of fuel
   System of release - the general information
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


https://glamorlady.ru: мотивация теория к защите
https://glamorlady.ru: мотивация теория к защите https://glamorlady.ru: мотивация теория к защите

Removal and installation of the fuel highway and injectors of fuel

See preventions at the beginning of the Section Dropping Pressure in a power supply system.

Removal of the fuel highway from the 4-cylinder engine can be made without preliminary dismantle of a delivery chamber of an air path. On V6 engines the delivery chamber has to be removed for the purpose of ensuring access to highways of the left and right ranks of cylinders, thus both highways can be removed uniform assembly together with the injectors fixed in them.

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for input of the equipment in action!

2. Dump pressure in a power supply system (see the Section Dropping Pressure in a power supply system).
3. On the V6 models uncover access the top part of the power unit (see the Head Dvigatel).
4. On the V6 models remove a delivery chamber of an air path (see the Head Dvigatel).

5. Disconnect an electrical wiring from injection injectors.

6. Disconnect a fuel return hose from pressure regulator.

The line of return of fuel is thinner and the hose of the giving fuel pipe (the pressure head line) pribolchen to the highway fastens on the regulator union a small collar of spring type, then.

7. Disconnect from the fuel highway of the tire of grounding.
8. Disconnect the line of supply of fuel from the fuel highway.

9. Give fixing nuts / bolts and remove the fuel highway of the engine.

On the V6 models of the highway of both rows of cylinders have to rise at the same time.

10. Take an injector(s) from the landing nest of the fuel highway.

11. Remove and will throw out old sealing and damping rings/washers.

It makes sense to replace all rings/washers used in injectors regardless of their state.

 

INSTALLATION

 PERFORMANCE ORDER

1. Oil new damping washers pure motive and put on them injection injectors.
2. Establish the new sealing rings (which are also oiled motive), then fill injectors in in the landing nests in the fuel highway.
3. Oil motive new landing sealing rings and fill them in nests under installation of injectors in the inlet pipeline.
4. Establish assembly of the fuel highway with injectors on the inlet pipeline. Tighten fixing nuts (4-cylinder models) with the demanded effort. On the V6 models strongly tighten fixing bolts.
5. Further installation is made as it should be, the return to an order of dismantle of components.
6. Having finished installation, without starting the engine, include ignition for the purpose of activation on couple of seconds of the fuel pump and rise in pressure in a power supply system. Repeat such inclusion two-three times, then check fuel lines, the highway and injectors for existence of signs of leaks.