Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
- Brake system
System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
Replacement of brake shoes of disk brake mechanisms
Removal and installation of supports of disk brake mechanisms
Check of a state, removal and installation of a brake disk
Replacement of boots of drum brake mechanisms of back wheels
Removal and installation of wheel cylinders
Removal and installation of the main brake cylinder
Check of a state and replacement of brake lines and hoses
Pumping of brake system
Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
Adjustment of the parking brake
Replacement of a cable(s) of the drive of the parking brake
Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
Check of serviceability of functioning and replacement of the sensor switch of level of brake fluid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment
|
Removal and installation of supports of disk brake mechanisms
|
|
Remember that the dust developed in the course of operation of brake mechanisms may contain extremely unhealthy the person asbestos. Do not blow off dust compressed air at all and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. Do not use for rubbing of components of brake system gasoline or solvents on an oil basis at all, - apply only firm cleaners or methyl alcohol!
Supports of both brake mechanisms of one axis have to change at the same time. |
Brake mechanisms of forward wheels
REMOVAL
|
|
|
1. Weaken wheel nuts. A car front also establish to Poddomkratta it on props. Remove wheels.
2. Disconnect from a support the hydraulic line, for the purpose of minimization of losses of brake fluid, and also, in order to avoid hit in a path of dirt to a zakuporta nipple connection.
|
|
3. Turn out fixing bolts. |
4. Remove a support from an anchor bracket. |
|
INSTALLATION
|
|
|
1. Installation is made upside-down. Do not forget to replace copper sealing washers (laying) from both parties of the nipple socket of connection to a support of a brake hose. Usually the set of new laying is applied in a remnabor. Tighten bolts of fastening of a support and a hollow bolt of nipple connection with the demanded effort.
2. Pump over a brake contour (see the Section Pumping of Brake System). Check nipple connections of brake lines for existence of signs of leaks.
3. Establish to the place of a wheel, lower the car on the earth and tighten nuts of fastening of wheels with the demanded effort (see Specifications to the Head Nastroyki and routine maintenance). Before starting operation of the car check serviceability of functioning of brakes. |
|
Brake mechanisms of back wheels REMOVAL
|
|
|
1. Weaken wheel nuts. A car back also establish to Poddomkratta it on props. Remove back wheels.
|
|
2. Release the lever of the parking brake, take a clamp and release a driving cable from the arm on the back party of a support of the brake mechanism. |
|
|
3. Disconnect a driving cable from the executive lever on a support. |
|
|
4. Turn out a hollow bolt of nipple connection of a brake hose on a support. Zakuporte of an opening by means of couple of pieces of a rubber hose. |
|
|
5. Turn out bolts of fastening of a support. |
6. Turn out bolts of fastening of a support |
|
INSTALLATION
|
|
|
1. Installation is made upside-down. Do not forget to replace sealing washers (laying) from both parties of the nipple socket of connection to a support of a brake hose. Usually the set of new laying is applied in a remnabor. Tighten bolts of fastening of a support and a hollow bolt of nipple connection with the demanded effort.
2. Pump over a brake contour (see the Section Pumping of Brake System). Check nipple connections of brake lines for existence of signs of leaks.
3. Establish to the place of a wheel, lower the car on the earth and tighten nuts of fastening of wheels with the demanded effort (see Specifications to the Head Nastroyki and routine maintenance). Before starting operation of the car check serviceability of functioning of brakes. |
|
|
|