The device, service and repair of Honda Accord - Check of an electric chain of the coupling of coupling of the K/V compressor//Honda the Chord of 1998-1999 of century /

Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
- Cooling systems, heating
   Antifreeze - general information
   Check of serviceability of functioning and replacement of the thermostat
   Check of a condition of fans of the cooling system and chains of their inclusion, replacement of fans
   Removal and installation of a radiator and broad tank of the cooling system
   Check of a condition of the water pump
   Replacement of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of the measuring instrument of temperature of cooling liquid
   Check of serviceability of functioning of a driving electric motor of the fan of a heater and condition of components of its electric chain, replacement of components
   Removal and installation of an electric motor of the drive of the fan of a heater
   Removal and installation of assembly of the control panel functioning of a heater and conditioner of air, adjustment of a driving cable
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Check of an electric chain of the coupling of coupling of the K/V compressor
   Removal and installation of a receiver dehumidifier To/in
   Removal and installation of the K/V compressor
   Removal and installation of the K/V condenser
   Removal and installation of the K/V evaporator with the broad valve
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment





Check of an electric chain of the coupling of coupling of the K/V compressor

 PERFORMANCE ORDER

1. Serviceability of functioning of the coupling of coupling of the compressor is pledge of trouble-free operation of the air conditioning system.
2. Warm up the engine up to the normal working temperature, transfer To/in to the mode of the maximum intensity of cooling and turn on the fan on the maximum speed. In order to avoid automatic shutdown of system open all doors of salon.
3. Ask the assistant to press the А/С button (To/in) and watch part of the compressor a lobby. The coupling of coupling has to publish clearly distinguishable click after which its central part will start rotating. If it does not occur, kill the engine and disconnect an electrical wiring from pressure sensor switch To / V. Peremknite of the electrical wiring plait socket plug by means of an office paper clip. If now coupling starts working normally, therefore excessive increase or pressure in system takes place. Drive away the car for more detailed diagnostics in a specialized workshop of car service.
4. If coupling of the compressor still does not work as it is required, check a condition of the corresponding safety locks, - take a safety lock No. 3 of the assembly block located at the left under the dashboard, and also a safety lock No. 58 of the large block located in a motive compartment (on a back partition).
5. Also remove the relay of coupling of the compressor (the assembly block in a motive compartment) and make check of serviceability of its functioning (see the Head Onboard electric equipment). At the taken relay and the switched-off ignition make sure available battery tension on the first nest of the relay (the scheme of an arrangement of contact plugs the same that for the fan relay). At the included ignition tension of the battery has to take place on a nest 4.
6. At the working engine and which is switched on To/in by means of wires crossing points connect nests 1 and 2 to the relay of coupling of the compressor, - at the time of connection the coupling has to publish distinct click.
7. If coupling still does not work, again switch off ignition, disconnect an electrical wiring from the coupling and by means of a long wire crossing point and an ohmmeter make sure available conductivity between the contact plug 2 on the plug of the relay of coupling and a compressor coupling socket nest. If conductivity is absent, check a chain for break on a site between the assembly block and the socket of the coupling. If conductivity takes place, Make sure of lack of break of a chain on a site between the assembly block and RSM.