Honda Accord

1998-1999 of release

Repair and operation of the car


Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
- Electric equipment of the engine
   General information and precautionary measures
   Start of the engine from the auxiliary power supply
   Check of a state and replacement of the battery
   Check of a state and replacement of wires of the battery
   System of ignition - the general information
   Check of functioning of system of ignition
   Check of a state and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management of ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation of a corner of an advancing of ignition
   System of a charge - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and installation of the generator
   Replacement of the regulator of tension and brushes of the generator
   System of start - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and installation of a starter
   Removal and installation of the traction relay
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment

Check of installation of a corner of an advancing of ignition

 PERFORMANCE ORDER

The procedure described below is calculated only on check of the basic installations made at manufacturer. Possibility of adjustments is not provided in view of what, the only purpose of the real check is the assessment of serviceability of functioning of the onboard processor. If during diagnostics of system of ignition (see the Section Check of Functioning of System of Ignition) it is not possible to reveal causes of infringement of installations of a corner of an advancing of ignition, it is necessary to replace RSM for what the car needs to be driven away on car repair shop.

1. Start the engine and warm up it up to the normal working temperature.
2. Check and, in case of need, adjust idling turns (see the Head Nastroyki and routine maintenance).

3. At the switched-off ignition find a label of VECI under a cowl and attentively study the instructions on installations of a corner of an advancing of ignition stated in it. Special value has correctness of installation of turns of idling as the frequency of rotation of the engine is directly connected with an ignition advancing corner. Prepare all necessary tools.

   - 1 - Vacuum traffic jams - All disconnected vacuum hoses have to be corked immediately. For this purpose traffic jams of various size and a configuration are issued
   - 2 - The stroboscope with inductive connection - Provides the pulsation of a bright, ostronapravlenny beam synchronized with the sparking moments on electrodes of a spark plug of the first cylinder. It is connected to VV to a wire of a candle of the first cylinder in compliance by instructions of manufacturers
   - 3 - The special wrench - On some models access to a clamping bolt of the distributor is limited and its otdavaniye with application of a key of a usual form becomes the extremely difficult

4. At the switched-off ignition, according to instructions of manufacturers connect a stroboscope. Food on a stroboscope usually moves from the onboard battery. The reception inductive sensor of a lamp is installed on VV a wire of a spark plug of the first cylinder (see Specifications to the Head Dvigatel).
5. A wire crossing point short-circuit among themselves plugs 8 and 13 of the diagnostic socket (DLC), is will transfer RSM to the mode of basic installations of a corner of an advancing of ignition.

6. Find adjusting distributive tags a pulley of a cranked shaft.

7. Start the engine, heated-up up to the normal working temperature, and direct a stroboscope beam on the adjusting index.
8. The red tag highlighted by a stroboscope beam on a pulley of a cranked shaft, remaining motionless, it has to be combined with the index.
9. At identification of violations in installations drive away the car on car repair shop for performance of diagnostics of RSM.
10. Kill the engine and remove a stroboscope.
11. Remove a wire crossing point from plugs of the diagnostic socket.