Honda Accord

1998-1999 of release

Repair and operation of the car


Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
- Electric equipment of the engine
   General information and precautionary measures
   Start of the engine from the auxiliary power supply
   Check of a state and replacement of the battery
   Check of a state and replacement of wires of the battery
   System of ignition - the general information
   Check of functioning of system of ignition
   Check of a state and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management of ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation of a corner of an advancing of ignition
   System of a charge - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and installation of the generator
   Replacement of the regulator of tension and brushes of the generator
   System of start - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and installation of a starter
   Removal and installation of the traction relay
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment

Формула рибальського успіху

Removal and installation of the distributor of ignition

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for input of the audio system in action!

2. Mark wires and hoses and disconnect them from the distributor.
3. Find the convex tag (in the form of figure or a letter) specifying location of the VV plug of a wire of a spark plug of the first cylinder on a distributor cover. If the cover is not equipped with marking of this sort, find the plug, having walked to it on a wire from a candle of the first cylinder, and put down the corresponding tag independently.
4. Uncover with the distributor (see the Head Nastroyki and routine maintenance) and turn a cranked shaft so that the runner was deployed by a nose towards position of the plug of a candle wire of the first cylinder on a cover (see the description of procedure of reduction of the engine in situation VMT in the Head Dvigatel).
5. Apply on edge of the case of the distributor, directly opposite to a runner nose parallel to an axis of the last, an orientation tag (if the runner has some noses, choose central). Mark also landing provision of the basis of the distributor the engine.

6. Give clamping a bolt(s) and take the distributor from the engine, having pulled it strictly vertically up.

In order to avoid data to zero efforts on drawing adjusting tags, do not allow a provorachivaniye of a cranked shaft after extraction of the distributor of ignition from the engine!

INSTALLATION

 PERFORMANCE ORDER

If the provorachivaniye of a cranked shaft at the ignition distributor taken from the engine was allowed, it is necessary to bring the engine into position VMT of the first cylinder (see appropriate section of the Head Dvigatel) and at installation of the distributor to achieve the relevant provision of its runner.

1. Put on a new sealing ring the distributor case.
2. Accurately fill the distributor in a reception nest in a head of cylinders. Achieve combination of the landing tags put in the course of dismantle.

Ledges at an end face of a shaft of the distributor and reciprocal grooves in an end face of a camshaft have an asymmetric arrangement that brings to naught possibility of installation of the distributor with a turn on 180 °.

3. If it is not possible to put completely the distributor, first of all, make sure of correctness of combination of landing tags, then achieve that the runner was deployed by a nose precisely towards a tag on the edge of the case.
4. Freely screw clamping a bolt(s).
5. Make further assembly as it should be, the return to a dismantle order. Check installation of a corner of an advancing of ignition, then strongly tighten clamping a bolt(s) of fastening of the distributor on the engine.