Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
- Coupling and power shafts
   Coupling - the general information and check of a condition of components
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Removal of air from a hydraulic path of the drive of switching off of coupling
   Removal, check of a state and installation of components of assembly of coupling
   Removal, check of a state and installation of the vyzhimny bearing and fork of switching off of coupling
   Adjustment of a pedal of coupling
   Check of a state, replacement and adjustment of the sensor switch of disconnection of a chain of a starter
   Removal and installation of power shafts
   Removal and installation of an intermediate shaft
   Replacement of protective covers and check of a condition of CV JOINTS
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Coupling - the general information and check of a condition of components

On all models equipped with RKPP one-disk coupling of dry type with a diaphragm spring is used. The nave of the frictional (conducted) disk is equipped with the longitudinal vents entering gearing with vents of a pin of primary shaft of transmission. Frictional and press disks of coupling keep in contact with each other due to the effort developed by a diaphragm spring of a press disk.

Switching off of coupling is made in the hydraulic way. The drive of switching off consists of a pedal of coupling, the main hydraulic cylinder with the tank, connecting lines and the executive cylinder making impact on the lever of switching off of coupling and vyzhimny the bearing.

When squeezing a pedal in a path of system the hydraulic pressure which is as a result put to the external end of the lever of switching off of coupling rises. At turn of the lever, fingers of its shaft rest in vyzhimny the bearing which, in turn, being displaced, nestles on petals of a diaphragm spring of a press disk in a coupling basket. Being curved, the spring interrupts contact of the press and conducted disks, releasing the last.

At coupling service, besides replacement of the components having obvious damages it is necessary to make some primary checks (it is supposed that the transmission is in good repair):

a) First of all it is necessary to check liquid level in the main hydraulic cylinder of coupling (see the Head Nastroyki and routine maintenance). In case of need make adjustment, having added the demanded amount of hydraulic liquid, and attentively examine system on existence of signs of leaks. At a devastation of the tank of the main cylinder it is necessary to remove from a hydraulic path air traffic jams (see the Section Removal of Air from a hydraulic path of the drive of switching off of coupling), then to check serviceability of functioning of coupling;
b) For an assessment of time of switching of coupling start the engine on normal turns of idling. Make sure that neutral transfer is included and release a coupling pedal. Now squeeze out a pedal of coupling and, having waited for some seconds, include a reverse gear. Switching should not lead to emergence of a gnash and other extraneous noises, with high degree of probability indicating malfunction of the conducted disk or assembly of a basket of coupling;
c) For check of completeness of switching off of coupling cock the parking brake and start the engine. Holding a coupling pedal at the height about 13 mm over a floor, a popereklyuchayta a transmission between the first and back transfers. Existence of hindrances when switching the lever speaks about malfunction of components of the mechanism of switching off. Estimate the course of a pusher of the executive cylinder of coupling. At completely squeezed out pedal the pusher has to move forward at a noticeable size, otherwise it is necessary to check the level of hydraulic liquid in the main cylinder;
d) Make visual check of a condition of axial plugs in the top part of a pedal of coupling. Make sure of lack of signs of jamming and an excessive side play of an axis;
e) Having got under the car, make sure of durability of landing of the lever of switching off of coupling on a spherical finger of a spherical support.