Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   - V6 engines
      Preparatory actions and the list of repair procedures which can be executed without extraction of the engine from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
      Removal and installation of covers of heads of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive
      Replacement of a forward epiploon of a cranked shaft
      VTEC system - the general information
      Removal, check of a state and installation of assembly of yokes
      Removal, check of a state and installation of camshafts
      Replacement of maslootrazhatelny caps and valvate springs with plates
      Removal and installation of heads of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a state and installation of the oil pump
      Removal and installation of a driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a state and replacement of support of a suspension bracket of the power unit (V6 Engines)
      System of correction of a suspension bracket of the power unit - the general information and check of serviceability of functioning
   + General and capital repairs of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Removal, check of a state and installation of assembly of yokes

REMOVAL

 PERFORMANCE ORDER

1. Uncover heads of cylinders (see the Section Removal and installation of covers of heads of cylinders).
2. Bring the piston of the first cylinder into situation VMT (see the Section Reduction of the Piston of the First Cylinder in the provision of the top dead point (TDP)), take off a gas-distributing belt (see the Section Removal, check of a state and installation of a gas-distributing belt and cogwheels of the GRM drive).

3. Weaken on 1/4 turns bolts of fastening of an axis of yokes (for weakening of the effort developed by valvate springs), - act as it should be, the return shown on an illustration.

4. Take assembly of an axis with yokes from a head of cylinders. Do not turn out fixing bolts finally for the purpose of fixing of components of assembly on an axis.

CHECK

 PERFORMANCE ORDER

1. Having removed assembly of yokes, it will be reasonable to investigate it for the purpose of more detailed studying of a condition of components. Turn out fixing bolts and remove from axes of a yoke and a spring. It will be reasonable to mark previously the provision of an axis in relation to covers of bearings.

It will be reasonable to fasten yokes of primary and secondary inlet valves with rubber bandages. Try to put the removed components as their installation as at assembly they have to be put strictly on the former places.

2. Carefully clear components and check them for existence of signs of wear and mechanical damages. Estimate a condition of the surfaces of yokes contacting to a camshaft, estimate degree of wear and freedom of rotation of rollers. Check for existence of zadir and signs of excessive wear of a surface of landing of yokes on axes, and also walls of landing openings of yokes. Defective components are subject to replacement. Make sure of passability of maslotok in axes.

3. Take from the landing nests in a head of cylinders proofreaders of valvate gaps and carefully clean them. Fingers check freedom of the course of plungers.
4. Check freedom of the course of the synchronizing pistons in assemblies of the drive of inlet valves.

INSTALLATION

 PERFORMANCE ORDER

1. Oil all components pure motive and establish them on the regular places on an axis of yokes.

Pay attention to the marking distinguishing left-side components from the right-hand.

2. Grease with special greasing for camshafts working surfaces of yokes. Put the removed components on an axis, then establish assembly on the engine.

3. In strictly certain order in stages (with a small step) tighten bolts of fastening of assembly of yokes with the demanded effort.

4. Installation of the remained components is made as it should be, the return to an order of their dismantle.
5. In summary do not forget to make adjustment of valvate gaps (if in it there is a need) (see the Head Nastroyki and routine maintenance).
6. Start the engine and check it for existence of signs of leak of oil and serviceability of functioning.