Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle / cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ Schemes of electric equipment





Removal and installation of overlays of forward and back bumpers

The models of cars considered in the present manual are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving injuries at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation.

Front bumper

 PERFORMANCE ORDER

1. Cock the parking brake, the car and establish to a poddomkratta it on props.
2. Disconnect a negative wire from the battery and wait not less than two minutes before starting dismantle of a slip.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for input of the audio system in action!

3. Under the car turn out screws of fastening of bottom edges of an overlay of a bumper.

For a poddevaniye of the central sections of plastic clamps use a small screw-driver (do not try to take completely the central sections, - they remain in a clamp).

4. Give screws of fastening of the upper edge of a slip to a cowl lock latch support. Remove a slip from the car.

5. Installation is made upside-down. Before rolling carving fixture make sure of reliability of a zashchelkivaniye of plastic clamps. In case of need use the help of the assistant.

Rear bumper

 PERFORMANCE ORDER

1. In case of need a car back also establish to a poddomkratta it on props.

2. Under the car take plastic clamps of fastening of bottom edge of an overlay of a rear bumper.

3. Turn out a bolt and release a clamp of fastening of each of the ends of a slip to arches of back wheels.

4. Open a trunk lid and from within a luggage compartment release clamps of fastening of the upper edge of an overlay of a bumper.

For a poddevaniye of the central sections of plastic clamps use a small screw-driver (do not try to take completely the central sections, - they remain in a clamp). Remove a slip from the car.

5. Installation is made upside-down.