Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle / cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ Schemes of electric equipment


National University of Ireland nui galway for international students education in Ireland.


Removal, installation and adjustment of provision of doors

For protection of hands against cuts when performing procedures through access openings in a doorframe put on gloves.

Doors of the car I have the considerable weight therefore it will be reasonable to secure with the help of the assistant.

REMOVAL AND INSTALLATION

 PERFORMANCE ORDER

1. Completely lower glass, then disconnect a negative wire from the battery.
2. Open a door against the stop and prop up it a jack, or wooden whetstones.
3. Remove the panel of an internal upholstery and the moisture filter (see the Section Removal and installation of panels of an internal upholstery of doors).
4. Mark and disunite all electric sockets, then release an electrical wiring from clamps on door assembly.
5. From a door separate laid between it and a body the rubber directing tube. Take the plait of an electrical wiring passed through the directing tube and remove it from a door.

6. Turn out a bolt of fastening of the limiter of opening of a door.

7. Lead round loopy levels a marker, having marked situation them on a door.
8. Ask the assistant to take a door and give bolts of fastening of loopy levels. Together remove a door from the car.

9. Installation is made upside-down.

ADJUSTMENT

 PERFORMANCE ORDER

1. Correctness of provision of a door in a body aperture has critical value from the point of view of serviceability of functioning of door assembly. First of all it is necessary to estimate the size of a side play of axial fingers of door loops. Completely open a door and pull it up-down. If the side play of a door exceeds 1.6 mm, loops should be replaced.

2. For performance of correction of the provision of a door in a body aperture weaken bolts of fastening of loops on a car body. The door can be considered established truly when in a closed position its upper edge is parallel to a car roof cut; the first line (back at a back door) doors thus has to appear aflush with a wing surface, and lower - with the threshold plane. If it is not possible to achieve an objective simple shift of loops, it is necessary to pick up adjusting washers of the necessary thickness. Washers are enclosed under loopy levels (both on a body, and on a door) and can be acquired in shops of automobile accessories.

3. Correct operation of the locking mechanism can achieve by updating of the provision of the drummer of the lock in the vertical direction. For an assessment of size of shift lead round a plate of the basis of the drummer a marker. Weaken fixture and make necessary adjustment, - the latch has to enter gearing with the central part of the drummer.
4. In summary adjust position of the drummer in the horizontal direction, - the closed door has to appear aflush with a surface of the rack/panel of a back wing and regularly thus be locked.