Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 Engines
   - General and capital repairs of the engine
      Check of pressure of oil
      Check of compression pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and installation of the engine
      Alternative versions of schemes of recovery repair of the engine
      Order of dismantling of the engine by preparation it to capital repairs
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a state and selection of inserts of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and running in of the engine after capital repairs
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment





Engine assembly order

Before starting assembly of the engine, make sure available all necessary details, materials and tools to which number the following belongs:

a) Standard set of the metalwork tool;
b) The Dinamometrichesky key with the drive on 1/2-dyuymv;
c) The tool for putting on of piston rings;
d) The tool for a staving of piston rings;
e) Short pieces of a fuel hose for putting on on hairpins of covers of shatunny bearings;
f) Measuring Plastigage set;
g) Set of probes of lezviyny type;
h) A file with small tooth;
i) Fresh motive oil;
j) Assembly motive or greasing on the basis of a molybdenum disulphate;
k) Pro-masonry sealant;
l) Sealant for fixing of threaded connections.

For saving of time and minimization of volume of the arising problems make assembly of the engine in the following order:

Four-cylinder engines

a) Piston rings;
b) Cranked shaft and radical bearings;
c) Shatunno-porshnevye;
d) Back epiploon of a cranked shaft;
e) Soyedinitelny Bridge of covers of radical bearings;
f) Maslootrazhatelny plate;
g) Balancing shaft;
h) Oil pump;
i) Maslozabornik with the mesh filter;
j) Case pallet;
k) Head of cylinders;
l) Camshaft and assembly of yokes;
m) A gas-distributing belt with cogwheels;
n) Cover of a gas-distributing belt;
o) Cover of a head of cylinders;
p) Inlet pipeline and final collector;
q) Flywheel / driving disk.

V6 engines


a) Piston rings;
b) Cranked shaft and radical bearings;
c) Shatunno-porshnevye;
d) A back epiploon of a cranked shaft with the holder;
e) Maslootrazhatelny plate;
f) Oil pump;
g) Case pallet;
h) Heads of cylinders;
i) Camshafts and components of the valvate mechanism;
j) A gas-distributing belt with cogwheels;
k) Covers of a gas-distributing belt;
l) Inlet pipeline and final collectors;
m) Covers of heads of cylinders;
n) Flywheel / driving disk.