Honda Accord

1998-1999 of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
- Engine management
   System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions
   Removal and PCM/ECM installation
   Check of serviceability of a state and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a state and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a state and replacement of the sensor of temperature of the soaked-up air (IAT)
   Check of serviceability of a state and replacement of the sensor of temperature of cooling liquid of the engine (eats)
   Check of serviceability of a state and replacement of the sensor of VMT/provision of a cranked shaft (TDC/CKP)
   Check of serviceability of a state and replacement of the sensor of position of pistons (CYP)
   Check of serviceability of a state and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a state and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a state and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a state and replacement of the sensor of a detonation
   Check of serviceability of a state and replacement of the sensor of speed of the movement of the car (VSS)
   Check of serviceability of functioning and replacement of the valve of stabilization of turns of idling (IAC)
   Check of serviceability of functioning and replacement of the air valve of correction of composition of air and fuel mix (FIA)
   System of the operated ventilation of a case (PCV)
   System of recirculation of the fulfilled gases (EGR) - the general information, check of a state and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a state and replacement of components
   The catalytic converter - the general information, check of a state and replacement
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Подводная охота на треску в Норвегии

Check of serviceability of a state and replacement of the sensor of temperature of cooling liquid of the engine (eats)

CHECK

 PERFORMANCE ORDER

1. The eats sensor represents a thermistor (the resistor which resistance changes with change of temperature). Change of resistance of the sensor has direct impact on amplitude of the signal which is given out to them on RSM. Thus, with REDUCTION of temperature resistance of the sensor INCREASES, and vice versa. Failure of the eats sensor leads to record in the block of memory of system of self-diagnostics of the P0116, P0117 or P0118 code.
2. Check of serviceability of functioning of the eats sensor is made by measurement of its resistance. Find the sensor and disconnect from it an electrical wiring.

3. Connect an ohmmeter to two plugs of assembly of the sensor. At a temperature about 20 °C the device has to register the indication around 2500 ÷ 3500 Ohms. Now start the engine and warm up it up to the normal working temperature (alternatively the sensor can be removed and heated-up up to the demanded temperature in a hot bathtub). Resistance of the sensor has to fall, and at a temperature about 83 °C to make 250 ÷ 350 Ohm. At negative results of the described check the eats sensor should be replaced.

If at the disconnected sensor the engine worked, do not forget to clear memory of system of self-diagnostics (see the Section System of Onboard Diagnostics (OBD) - the principle of functioning and codes of malfunctions).

REPLACEMENT

 PERFORMANCE ORDER

Before starting procedure performance, wait for full cooling of the engine.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for input of the audio system in action!

2. Before installation of the new sensor its carving part should be wound with a teflon sealing tape (tape FUM).
3. Wring out a lock uvula, disconnect an electrical wiring, then accurately turn out the sensor. For the purpose of minimization of losses of cooling liquid try to screw the replaceable sensor as soon as possible.

Handle the eats sensor as it is possible more carefully as its damage is capable to have noticeable impact on functioning of a power supply system in general.

4. Installation is made upside-down. In summary check the level of cooling liquid, in case of need make the corresponding adjustment (see the Head Nastroyki and routine maintenance).